Re: dc0: MII without any PHY!

From: Ajit Warrier <unixajit(at)yahoo.com>
Date: Wed Nov 20 2002 - 12:58:53 EST

Hi Dan,

I thought it would be automatically created. At any rate, I added the file manually. The problem is the same. The output of dmesg and ifconfig -a follow -

-----------------------Start
dmesg---------------------

OpenBSD 3.2 (GENERIC) #25: Thu Oct 3 19:51:53 MDT 2002    

deraadt@i386.openbsd.org:/usr/src/sys/arch/i386/compile/GENERIC cpu0: Intel Pentium II ("GenuineIntel" 686-class, 512KB L2 cache) 232 MHz
cpu0:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,SYS,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR real mem = 66498560 (64940K)
avail mem = 56123392 (54808K)
using 837 buffers containing 3428352 bytes (3348K) of memory
mainbus0 (root)
bios0 at mainbus0: AT/286+(cf) BIOS, date 04/02/98, BIOS32 rev. 0 @ 0xfd820
apm0 at bios0: Power Management spec V1.2 apm0: AC unknown, no battery
pcibios0 at bios0: rev. 2.1 @ 0xfd880/0x800 pcibios0: PCI IRQ Routing Table rev. 1.0 @ 0xfb2b0/96 (4 entries)
pcibios0: PCI Exclusive IRQs: 11
pcibios0: PCI Interrupt Router at 000:07:0 ("Intel 82371AB PIIX4 ISA" rev 0x00)
pcibios0: PCI bus #2 is the last bus
bios0: ROM list: 0xc0000/0xa000
pci0 at mainbus0 bus 0: configuration mode 1 (no bios) pchb0 at pci0 dev 0 function 0 "Intel 82443BX" rev 0x02
cbb0 at pci0 dev 2 function 0 "Texas Instruments PCI1250 PCI-CardBus" rev 0x02: irq 11
cbb1 at pci0 dev 2 function 1 "Texas Instruments PCI1250 PCI-CardBus" rev 0x02: irq 11
vga1 at pci0 dev 3 function 0 "Neomagic Magicgraph NM2160" rev 0x01
wsdisplay0 at vga1: console (80x25, vt100 emulation) wsdisplay0: screen 1-5 added (80x25, vt100 emulation) pcib0 at pci0 dev 7 function 0 "Intel 82371AB PIIX4 ISA" rev 0x01
pciide0 at pci0 dev 7 function 1 "Intel 82371AB IDE" rev 0x01: DMA, channel 0 wired to compatibility, channel 1 wired to compatibility
wd0 at pciide0 channel 0 drive 0: <IBM-DYKA-23240> wd0: 16-sector PIO, LBA, 3102MB, 6304 cyl, 16 head, 63 sec, 6354432 sectors
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2 atapiscsi0 at pciide0 channel 1 drive 0
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: <TOSHIBA, CD-ROM XM-1702BC, 1562> SCSI0 5/cdrom removable cd0(pciide0:1:0): using PIO mode 4, DMA mode 2 uhci0 at pci0 dev 7 function 2 "Intel 82371AB USB" rev 0x01: irq 11
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: vendor 0x0000 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered "Intel 82371AB Power Mgmt" rev 0x01 at pci0 dev 7 function 3 not configured
cardslot0 at cbb0 slot 0 flags 0
cardbus0 at cardslot0: bus 1 device 0 cacheline 0x8, lattimer 0xb0
pcmcia0 at cardslot0
cardslot1 at cbb1 slot 1 flags 0
cardbus1 at cardslot1: bus 2 device 0 cacheline 0x8, lattimer 0xb0
pcmcia1 at cardslot1
isa0 at pcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0 pms0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
sb0 at isa0 port 0x220/24 irq 5 drq 1: dsp v3.02 midi0 at sb0: <SB MIDI UART>
audio0 at sb0
opl0 at sb0: model OPL3
midi1 at opl0: <SB Yamaha OPL3>
pcppi0 at isa0 port 0x61
midi2 at pcppi0: <PC speaker>
sysbeep0 at pcppi0
lpt2 at isa0 port 0x3bc/4: polled
npx0 at isa0 port 0xf0/16: using exception 16 pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec biomask c840 netmask c840 ttymask d842
pctr: 686-class user-level performance counters enabled
mtrr: Pentium Pro MTRR support
dkcsum: wd0 matched BIOS disk 80
root on wd0a
rootdev=0x0 rrootdev=0x300 rawdev=0x302
dc0 at cardbus1 dev 0 function 0 irq 11 address 00:10:a4:aa:2d:b6
dc0: MII without any PHY!

------------------------End
dmesg----------------------


---------------------Start
ifconfig--------------------

lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 33224

	inet 127.0.0.1 netmask 0xff000000 
	inet6 ::1 prefixlen 128
	inet6 fe80::1%lo0 prefixlen 64 scopeid 0x3
lo1: flags=8008 mtu 33224
pflog0: flags=0<> mtu 33224

sl0: flags=c010<POINTOPOINT,LINK2,MULTICAST> mtu 296 sl1: flags=c010<POINTOPOINT,LINK2,MULTICAST> mtu 296

ppp0: flags=8010 mtu 1500
ppp1: flags=8010 mtu 1500
tun0: flags=10 mtu 3000
tun1: flags=10 mtu 3000
enc0: flags=0<> mtu 1536

bridge0: flags=0<> mtu 1500
bridge1: flags=0<> mtu 1500
vlan0: flags=0<> mtu 1500

        address: 00:00:00:00:00:00
vlan1: flags=0<> mtu 1500

        address: 00:00:00:00:00:00

gre0: flags=9010 mtu 1450
gif0: flags=8010 mtu 1280
gif1: flags=8010 mtu 1280
gif2: flags=8010 mtu 1280
gif3: flags=8010 mtu 1280

---------------------End ifconfig--------------------

 Dan Heaver <Dan.Heaver@fdmgroup.com> wrote:
> Have you tried creating a /etc/hostname.dc0 file ?
>
deraadt@i386.openbsd.org:/usr/src/sys/arch/i386/compile/GENERIC
> cpu0: Intel Pentium II ("GenuineIntel" 686-class,
>
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,SYS,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR
> real mem = 66498560 (64940K)
>

---

> This e-mail has been scanned for all viruses by Star
> Internet. The
> service is powered by MessageLabs. For more
> information on a proactive
> anti-virus service working around the clock, around
> the globe, visit:
> http://www.star.net.uk

>

---

>

>

---

> This e-mail has been scanned for all viruses by Star
> Internet. The
> service is powered by MessageLabs. For more
> information on a proactive
> anti-virus service working around the clock, around
> the globe, visit:
> http://www.star.net.uk

>

---

Yahoo! Web Hosting - Let the expert host your site http://webhosting.yahoo.com Received on Wed Nov 20 13:00:34 2002