IBM Microdrive on USB not recognized

From: John R. Shannon <john(at)johnrshannon.com>
Date: Tue Dec 03 2002 - 15:59:36 EST

-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1

I'm using OpenBSD3.2-STABLE with a generic kernel, an OnSpec "One for All Flash Media Drive (Console) B29911" (USB) and an IBM microdrive. The firmware is recognizing the drive, but only the controllers are showing up in dmesg (at end of post). The Intel D845GEBG2 motherboard is based on the 845E chipset.

usbdevs -v shows the following:

Controller /dev/usb0:
addr 1: self powered, config 1, UHCI root hub(0x0000), vendor 0x0000(0x0000), rev 1.00
 port 1 powered
 port 2 powered
Controller /dev/usb1:
addr 1: self powered, config 1, UHCI root hub(0x0000), vendor 0x0000(0x0000), rev 1.00
 port 1 powered
 port 2 powered
Controller /dev/usb2:
addr 1: self powered, config 1, UHCI root hub(0x0000), vendor 0x0000(0x0000), rev 1.00
 port 1 powered
 port 2 enabled

Are there known problems with this device? Is there a USB interface that works with IBM microdrives? The microdrive has a CF+ interface but draws a lot of power (250-260ma during write).

This dmesg is from a boot with the microdrive plugged in:

OpenBSD 3.2-stable (GENERIC) #1: Mon Dec 2 13:38:44 MST 2002

    root@brigid.johnrshannon.com:/usr/src/sys/arch/i386/compile/GENERIC cpu0: Intel Pentium 4 ("GenuineIntel" 686-class) 2.40 GHz cpu0:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SYS,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SIMD real mem = 535670784 (523116K)
avail mem = 489328640 (477860K)
using 4278 buffers containing 26886144 bytes (26256K) of memory mainbus0 (root)
bios0 at mainbus0: AT/286+(00) BIOS, date 05/29/02, BIOS32 rev. 0 @ 0xf0010 pcibios0 at bios0: rev. 2.1 @ 0xf0000/0x10000

pcibios0: PCI IRQ Routing Table rev. 1.0 @ 0xf4670/192 (10 entries)
pcibios0: PCI Interrupt Router at 000:31:0 ("Intel 82371FB PCI-ISA" rev 0x00)
pcibios0: PCI bus #2 is the last bus

bios0: ROM list: 0xc0000/0x8000 0xc8000/0x5600 0xcd800/0x1800 0xcf000/0x1000 pci0 at mainbus0 bus 0: configuration mode 1 (no bios) pchb0 at pci0 dev 0 function 0 "Intel 82845 Host" rev 0x11 ppb0 at pci0 dev 1 function 0 "Intel 82845 AGP" rev 0x11 pci1 at ppb0 bus 1
vga1 at pci1 dev 0 function 0 "ATI Rage 128 Pro TF" rev 0x00 wsdisplay0 at vga1: console (80x25, vt100 emulation) wsdisplay0: screen 1-5 added (80x25, vt100 emulation) uhci0 at pci0 dev 29 function 0 "Intel 82801DB USB" rev 0x01: irq 11 usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: vendor 0x0000 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub0: 2 ports with 2 removable, self powered uhci1 at pci0 dev 29 function 1 "Intel 82801DB USB" rev 0x01: irq 11 usb1 at uhci1: USB revision 1.0
uhub1 at usb1
uhub1: vendor 0x0000 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub1: 2 ports with 2 removable, self powered uhci2 at pci0 dev 29 function 2 "Intel 82801DB USB" rev 0x01: irq 5 usb2 at uhci2: USB revision 1.0
uhub2 at usb2
uhub2: vendor 0x0000 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub2: 2 ports with 2 removable, self powered
"Intel 82801DB USB" rev 0x01 at pci0 dev 29 function 7 not configured
ppb1 at pci0 dev 30 function 0 "Intel 82801BA AGP" rev 0x81 pci2 at ppb1 bus 2
ahc1 at pci2 dev 1 function 0 "Adaptec AHA-29160 U160" rev 0x02: irq 10 ahc1: aic7892: Ultra160 Wide Channel A, SCSI Id=7, 32/255 SCBs scsibus0 at ahc1: 16 targets
ahc1: target 5 synchronous at 10.0MHz, offset = 0xf st0 at scsibus0 targ 5 lun 0: <Quantum, DLT4000, D991> SCSI2 1/sequential removable
st0: density code 0x1a, variable blocks, write-enabled ahc2 at pci2 dev 2 function 0 "Adaptec AHA-3960D U160" rev 0x01: irq 5 ahc2: aic7899: Ultra160 Wide Channel A, SCSI Id=7, 32/255 SCBs scsibus1 at ahc2: 16 targets
ahc3 at pci2 dev 2 function 1 "Adaptec AHA-3960D U160" rev 0x01: irq 11 ahc3: aic7899: Ultra160 Wide Channel B, SCSI Id=7, 32/255 SCBs scsibus2 at ahc3: 16 targets
ahc3: target 0 synchronous at 80.0MHz DT, offset = 0x3f ahc3: target 0 using tagged queuing
sd0 at scsibus2 targ 0 lun 0: <SEAGATE, ST318406LW, 010A> SCSI3 0/direct fixed sd0: 17501MB, 26302 cyl, 2 head, 681 sec, 512 bytes/sec, 35843670 sec total
"Intel PRO/100 VE" rev 0x81 at pci2 dev 8 function 0 not configured
fxp0 at pci2 dev 12 function 0 "Intel 82557" rev 0x0c: irq 11, address 00:02:b3:a8:0f:fc
inphy0 at fxp0 phy 1: i82555 10/100 media interface, rev. 4 pcib0 at pci0 dev 31 function 0 "Intel 82801DB LPC" rev 0x01 pciide0 at pci0 dev 31 function 1 "Intel 82801DB IDE" rev 0x01: DMA, channel 0 configured to compatibility, channel 1 configured to compatibility pciide0: channel 0 ignored (disabled)
atapiscsi0 at pciide0 channel 1 drive 0
scsibus3 at atapiscsi0: 2 targets
cd0 at scsibus3 targ 0 lun 0: <SONY, CD-RW CRX195E1, ZYS5> SCSI0 5/cdrom removable
cd0(pciide0:1:0): using PIO mode 4, Ultra-DMA mode 2
"Intel 82801DB SMB" rev 0x01 at pci0 dev 31 function 3 not configured
auich0 at pci0 dev 31 function 5 "Intel 82801DB AC97 Audio" rev 0x01: irq 11, ICH4 AC97
ac97: codec id 0x41445372 (Analog Devices AD1981A) ac97: codec features headphone, 20 bit DAC, No 3D Stereo audio0 at auich0
isa0 at pcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0 pms0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
sysbeep0 at pcppi0
lpt0 at isa0 port 0x378/4 irq 7
npx0 at isa0 port 0xf0/16: using exception 16 pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo pccom1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
biomask 8c60 netmask 8c60 ttymask 9ce2
pctr: user-level cycle counter enabled
dkcsum: sd0 matched BIOS disk 80
root on sd0a
rootdev=0x400 rrootdev=0xd00 rawdev=0xd02

• --

John R. Shannon
john@johnrshannon.com

-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.2.1 (FreeBSD)

iEYEARECAAYFAj3tGzgACgkQOKbCxya4HYsqFQCglKGilrdpZXSUIQjh6jqUsZwC OmUAn2SqTukwQEuDaqliXSOK13vI2mzi
=ArAJ
-----END PGP SIGNATURE----- Received on Tue Dec 3 16:02:11 2002